Outerworld Arcade
Armor Attack

Cinematronics Monitor
Vertical Deflection Repair

Armor Attack Without Vertical DeflectionI had a my Armor Attack running for a few hours a couple of days ago. As I walked by I heard the circuit breakers click and the game shut off. I unplugged the game and reset the breakers. After plugging it back in and turning it on I saw the game was playing, but the image on the monitor was crushed into a thin horizontal area that looked something like the image to the right. Then the circuit breakers blew again.

I looked back at the monitor only to see a puff of smoke coming from resistor R118. One of the vertical transistors had gone bad and smoked R118 in the process. This problem is very common on Cinematronics vector games. Luckily, it’s not too hard to fix.

After reviewing the Cinematronics Guide, I bought a few 47 Ohm, 5w resistors to replace the burnt R118. For the transistors, I looked for the replacement suggested by the The Cinematronics Vector Monitor FAQ and Repair Guide.

Here is a description of the complete replacement procedure:

In preforming these modifications, there are many opportunities for harm to yourself or your equipment.

You perform these modifications AT YOUR OWN RISK!!!

Replacement parts needed:
2- 47 Ohm, 5w resistors
2- Transistors

Tools needed:
Screwdrivers
Soldering Iron, Sucker, and Solder
Digital Multimeter

Remove the monitor from the cabinet

1. Turn off and unplug machine.

2. Remove the ribbon cable from the back of the monitor, noting its orientation when plugged into the monitor. It can be plugged in backwards which can cause damage to the monitor.

3. Remove the molex power cable from the monitor. It is keyed and should only plug in one way.

 

4. Carefully remove the two wing nuts from the corner of the bracket that holds the monitor frame while holding on to the monitor so that it doesn't drop. There's no particularly easy place to hold it - but avoid touching the yoke or the anode (suction cup looking thing attached to the tube).

5. Lower the monitor so that it sits face-up inside the cabinet.
6. Remove the screws holding the monitor to the frame. The far left corner will be more challenging to get to since it is blocked by the deflection transistor heat sinks.
7. Carefully slide the monitor out from the rear of the cabinet and set it somewhere safe to work on. The weight in the monitor is not balanced and will want to tip towards the face of the tube, so set it somewhere where it can't tip over. Cinematronics Monitor

Replace the deflection transistors

1. Pull the molex plug attaching the deflection transistors to the monitor chassis PCB.

2. Unscrew the deflection transistors with their heat sink from the monitor frame.

3. You will need to replace both transistors, but can test to see which is bad using the "testing transistors" section in the The Cinematronics Vector Monitor FAQ and Repair Guide.

4. Unscrew the each transistor and pull them from their socket. Remove both transistor and the plastic spacer.

5. Replace each with the plastic spacer and appropriate transistor, note that the vertical and horizontal deflection transistors are in the opposite locations on the heat sink.

6. Test to verify proper installation.

7. Feed Molex plug back through monitor frame and re-attach heat sink to monitor frame.

8. Plug molex plug back into appropriate socket on monitor chassis PCB.

Deflection transistors removed

Replace resistors R118 & R119

1. Clip and desolder burnt resistor R118. For good measure, remove resistor R119 as well to ensure it won't burn up in the future. Burnt Resistor R118
2. Replace each with 47 Ohm, 5w resistor. This replacement resistor won’t burn like the original did, but is too big to fit on the parts side of the monitor chassis PCB. So solder in the new resistor on the bottom of the PCB.
3. When finished, the chassis board should look like this with the new resistors installed. Resistors Installed

 

Replace the monitor in the cabinet

1. Carefully slide the monitor onto the brackets inside the cabinet.

2. Attach the screws holding the monitor to the frame.

3. Plug in the Molex power cable from the monitor. It is keyed and should only go plug in one way.

4. Plug in the ribbon cable to the back of the monitor in its proper orientation.

5. Plug in and turn on the game. Look for proper picture!

6. If all looks well, turn the game back off and raise the monitor so that the holes in the monitor brackets line up with the holes in the sides of the cabinet. Slide in the carriage bolts to hold the monitor in place and screw on the wing nuts on the corner of the bracket the holds the monitor frame.

Armor Attack Picture Bacl